frictional heat中文是什么意思

發音:

中文翻譯
造句

摩擦熱

frictional n. 摩擦的，由摩擦而生的。 adv. -ly
heat n. 1.熱；熱力；熱度；熱量。 2.體溫；發燒。 3. ...
frictional heat build-up 摩擦生熱
frictional heat energy 摩擦熱能
frictional heat gain 摩擦熱量增量; 摩擦熱增加; 摩擦增熱
frictional heat source 摩擦熱源
internal frictional heat 內摩擦熱
frictional n. 摩擦的，由摩擦而生的。 adv. -ly
force, frictional 摩擦力
frictional alloying 摩擦合金法
frictional angel 摩擦角
frictional angle 磨擦角; 摩擦角
frictional area 摩擦面積
frictional arking 摩擦打火
frictional attachment 磨擦附著
frictional behavior 磨擦性能
frictional belt 摩擦區
frictional binding 摩阻粘合
frictional brake 磨擦閘
frictional characteristic 摩擦特性
frictional clutch 磨擦離合器; 摩擦離合器; 摩擦聯結器
frictional coefficient 磨擦系數; 摩擦系數
frictional compensation 摩擦補償
frictional conformability 摩擦順應性
frictional conpatibility 摩擦相容性

"查查詞典"手機版

千萬人都在用的超大詞匯詞典翻譯APP

例句與用法

This depends on the estimation of the temperatures generated by frictional heat .
它取決于摩擦熱所引起的溫度估算。
The result shows that it is mainly caused by the martensite with high hardness produced after rail absorbing frictional heat
斷裂的主要原因是鋼軌在吸收摩擦熱后產生了高硬度的馬氏體。
The biggest fuel savings achieved by a full hybrid vehicle derives from regenerative braking , a technology that captures as electrical power much of the energy normally lost as frictional heat
高量級混合車最大的省油關鍵來自再生制動（煞車）技術，這種技術可捕集摩擦熱（通常幾乎散失掉的能量）并轉變成電力。
The effect of the variation of temperature and contact pressure of the sliding contact surfaces with frictional heating on each other , particularly the relationship of the applied pressure and the contact pressure and the effect of the separate variation of some parameters on the simulation results were taken account into in the course of numerical simulation
在數值計算過程中，著重考慮了溫度變化與接觸區域壓力變化的耦合問題，接觸壓力與外加壓力的關系，以及分別改變一些參數對結果的影響。
The fem results indicated that as to the rough surfaces in sliding contact , the value of the contact pressure was very high which coursed a high value of the heat flow rate , meanwhile the sliding time was not enough for the frictional heat to transfer , thus the highest value of the body temperature occurred just on the sliding surfaces , which possessed a sharp thermal gradient in direction perpendicular to the sliding surface . so the great thermal stress was caused just by the sharp gradient and the thermal elastic distortion with which the contact pressure changed occurred simultaneously , thus this change of the contact pressure would affect the temperature distribution in return
對于相對滑動的粗糙表面，因實際接觸面積小而導致接觸壓力很大，這樣使得熱流密度會很大，同時由于滑動時間很短，熱來不及傳導，最高溫度發生在摩擦表面，在垂直于摩擦面的方向有很大的溫度梯度，使得熱應力很大，且最大應力發生在表面，同時產生熱彈性變形，這種變形使得接觸區域內的壓力分布發生變化，這種變化又反過來影響了接觸區域的溫度分布。
Based on g - w contact model , two rough surfaces in contact were simplified to a smooth one and a rough one which has regular rectangular asperities , and a three - dimensional transient thermal and stress coupled fem model was established using thermal - structure sequential coupling . the course of the sliding with friction was simulated using the nonlinear multiphysics field fem , meanwhile considering thermal - elastic problems of the two bodies , to calculate and analyze the temperature , contact pressure and stress of the sliding contact surfaces with frictional heating
基于g - w接觸模型，將兩個粗糙表面簡化為一個有規則排列的長方體微凸體的粗糙表面與一光滑表面，利用熱結構順序耦合建立三維瞬態有限元計算模型，考慮兩個物體摩擦接觸的熱彈性問題，采用非線性有限元多物理場來實現，對粗糙表面接觸模型的瞬時摩擦溫度場、壓力場和應力場進行了計算分析。
Based on the theories of gear engagement , contact analysis , friction and heat transfer , a three - dimensional finite element model of gear tooth was established to investigate temperature distributions and variations along the contact path over a range of applied loads and operating speeds with consideration of lubrication conditions . sensitivity analysis of surface temperature to gear configuration , frictional heat flux , heat transfer coefficients , and oil and ambient temperature was conducted and the major parameters influencing surface temperature were evaluated
本文基于齒輪嚙合原理、輪齒接觸分析、摩擦學和傳熱學，以有限元分析方法和理論分析計算相結合為手段并以實驗測量結果作為參考，建立了適用于工業應用并具有較高計算精度的高速齒輪傳動輪齒溫度分析的模型和方法，系統地分析了輪齒本體溫度的大小和分布以及齒輪幾何、載荷及轉速和潤滑冷卻條件等對輪齒本體溫度的影響。
Many kinds of the heat sources ( frictional heat , cutting heat , ambient temperature , etc ) in machining system produce a kind of temperature distribution . this temperature distribution induces thermal deformation between machine tools , tool , work - piece and work holding fixture . this deformation affects the relative displacement between the work piece and the cutter , causes the manufacturing errors , and influences the machining accuracy of the work - piece
在機械加工中，工藝系統在各種熱源(摩擦熱、切削熱、環境溫度、熱輻射等)的作用下，產生溫度場，致使機床、刀具、工件、夾具等產生熱變形，從而影響工件與刀具間的相對位移，造成加工誤差，進而影響零件的加工精度。